I-Drive (Callaway FT-i clone) 460cc Drivers

I-Drive Square 460cc Driver Head
Integra I-Drive (Callaway FT-i clone) 460cc Drivers

Final (Callaway FT-i clone) 460cc Drivers

Final 460cc (Callaway FT-i clone) Square Titanium Driver Head
Final (Callaway FT-i clone) 460cc Drivers
 

• The square head increases the club head's Moment of Inertia (MOI) or reduced twisting during off-center hits.
• High MOI face keep the ball straight and long down the fairway!
• Squared face geometry enlarges the hitting area and increases forgiveness.
• Moving the center of gravity farther back raises the launch angle thereby making the clubface easier to square for straighter drives.
• Variable face thickness in the face, sole and back wall controls clubhead deformation for maximum energy transfer, reduced spin and high launch angle.

See Golf Digest December 2006 issue for article on Nike™ and Callaway™ Square Golf Clubs.  Square golf clubs from Nike and Callaway will not be available until January 2007 and will cost $400 - $500, but you can try the Final 460cc Square driver now and start hitting dead straight drives now. Everyone knows that a straight drive goes longer than a crooked drive.

SV2 PLUS, SV3 Square (Nike Sumo clone) 460cc Drivers

With the latest design geometry in the golf industry the SV3 produces a shot with maximum forgiveness.  The square design places more weight behind the face at the heel and toe positions.  Along with the scalloped crown this produces a very low center of gravity creating a higher launch angle with a low spin rate.

The SV3's & SV2 Plus advanced design features break down to:

For assembled custom built drivers go to SV3, SV2 PLUS Titanium Drivers
For assembled custom built LADIES drivers go to Ladies SV2 PLUS, SV3 Titanium Drivers
For assembled custom built SENIORS drivers go to Seniors SV2 PLUS, SV3 Titanium Drivers

PGR Raptor Set of Iron Heads (Ping Rapture clone)

• Maximum Perimeter Weighting – Head geometry that maximizes the perimeter weighting, which substantially increases the moment of inertia for maximum forgiveness on off-center shots, while generating a very high, straight trajectory.
• Wide Sole Design – The wide sole has positioned the CG further back to promote a high trajectory and lower spin for high soft shots into the green that don't balloon in the wind. This sole design also provides easy transition through the turf for solid ball contact.
• Deep Undercut Cavity Design – Cavity is parallel to the ground allowing more mass to be moved away from the club face, creating a wide sole and high moment of inertia for maximum forgiveness on off-center shots.
• Extraordinary Aesthetics – Fine satin finish gives the club a deep, rich look while providing exceptional durability.

Raptor Ping Clone Iron Heads
Steel Shafted PGR Raptor Set of Irons (Ping Rapture clone)
Graphite Shafted PGR Raptor Set of Irons (Ping Rapture clone)

Turbo Power Three Ball II (Odyssey SRT Tri-Ball  clone) Putter

The new Turbo Power Three Ball II putter is a hyper extended perimeter weighted design to give it the highest MOI (moment of inertia) to reduce twists upon impact.  This is achieved through a high density semi-circular weight at the rear which pushes the center of gravity towards the perimeter and behind the face.  This coupled with a CNC milled, high quality stainless steel face with a loft of five degrees, makes your putts roll with less skidding to follow a straighter line.  This putter may be assembled with either a straight shaft or a double bend shaft to make an off-set putter design.

Turbo Power Three Ball II (Odyssey SRT Tri-Ball  clone) Putter Head
Turbo Power Three Ball II (Odyssey SRT Tri-Ball  clone) Putter

MCS Graphite Golf Shafts MCS 2.8 Ultra Graphite Wood Shaft Compare to Aldila NV $29.00 MCS 75 Graphite Wood Shaft Compare to Apache MFS65$19.00 MCS 70 Graphite Wood Shaft Compare to Apache MFS65$19.00 MCS E=MC2 Graphite Wood Shaft Compare to Aldila NV$19.00